CfgSurfaces Config Reference – Arma 3
Template:Cfg ref Template:Cfg ref
A
access
Integer: Determines the manipulability of the class.
| Value | Type | Description |
|---|---|---|
| 0 | ReadAndWrite | Additional values can be added |
| 1 | ReadAndCreate | Only adding new class members is allowed |
| 2 | ReadOnly | No modifications enabled |
| 3 | ReadOnlyVerified | No modifications enabled |
All BIS classes are ReadOnlyVerified and can only be inherited into a new class
access = 2; // ReadOnly
AIAvoidStance
1.60
Integer: Allows restricting the AI from entering prone with two levels of emphasis
| Value | Description |
|---|---|
| 0 | No change in behavior |
| 1 | Less preference for going prone |
| 2 | Almost never going prone |
C
character
String: Points to a corresponding CfgSurfaceCharacters entry, which defines the clutter on this surface.
character = "Empty"; // No clutter will be used on this surface
character = "SeabedClutter"; // SeabedClutter defined in CfgSurfaceCharacters will be used on this surface
D
dust
Float: Amount of dust vehicles will create on this surface (higher value = more dust)
dust = 0.75; // High amount of dust, used for GdtStratisDryGrass
dust = 0.05; // Almost no dust, used for GdtConcrete
F
files
String: Defines which ground texture and roadway texture filenames this surface will apply to
files = "gdt_grass_green_*"; // Tells the ground texture what surface it corresponds to
files = "surfint_wood_*"; // Tells the texture used in the roadway LOD what surface it corresponds to
From commented configs of BI (binarize\bin)
Caution: wildcard pattern "files" is matched using special purpose matching * may be used only as last character of the pattern * matches any string in filename ? matches any single character in filename when six trailing question-marks are detected "??????", two patterns are matched: full pattern and short pattern with ?????? omitted
friction
Float: Unknown
friction = 0.9; // Default value, used by all A3 surfaces
G
grassCover
Float: Used to simulate grass cover at a distance by sinking the target into the ground (higher value = more sinking)
grassCover = 0; // Used by GdtStratisConcrete, there will be no simulated grass cover at a distance
grassCover = 0.05; // Used by GdtStratisGreenGrass, there will be some simulated grass cover at a distance
I
impact
String: Defines what particle effect is shown when the surface is hit by a bullet, points to a corresponding entry in CfgAmmo
impact = "hitGroundHard"; // Used by GdtStony, particle effect will be chunks of rock flying when hit
impact = "hitGroundSoft"; // Used by GdtStratisDirt, particle effect will be dirt flying when hit
Check the spoiler for impact values used in vanilla A3 in 1.68:
default_Mat hitWater hitGroundHard hitConcrete hitGroundSoft hitVirtual HitGroundRed hitGroundRed
isWater
Integer: Declares whether the surface is water
isWater = 1; // Used by SurfWater, declares the surface as water
isWater = 0; // Used by Default, declares the surface is not water
L
lucidity
Float: Unknown
lucidity = 0.3; // Used by GdtStratisConcrete
lucidity = 3.5; // Used by GdtStratisForestPine
lucidity = 150; // Used by GdtStratisSeabed
M
maxClutterColoringCoef
Float: Defines the maximal coefficient of difference between the color of the surface and clutter (must be greater than or equal to 1)
maxClutterColoringCoef = 1.35; // Used by GdtStratisConcrete
maxClutterColoringCoef = 1.5; // Used by GdtBeach
maxSpeedCoef
Float: Defines the maximum speed coefficient on that surface
maxSpeedCoef = 1; // Used by GdtStratisConcrete, no change in speed
maxSpeedCoef = 0.9; // Used by GdtStratisGreenGrass, 10% reduction in speed
maxSpeedCoef = 0.8; // Used by GdtStratisForestPine, 20% reduction in speed
R
restitution
Float: Unknown
restitution= 0; // Used by every surface
rough
Float: Defines the roughness of the surface when driving over it in a vehicle (higher value = more bumps)
rough = 0.05; // Used by GdtStratisConcrete, minimal bumps
rough = 0.15; // Used by GdtMud, fairly bumpy
S
soundEnviron
String: Defines the sound played when walking or driving a vehicle on the surface, points to sounds defined in SoundEnvironExt
soundEnviron = "drygrass"; // Used by GdtGrassDry, dry grass sound
soundEnviron = "gravel"; // Used by SurfRoadDirt, gravel sound
soundEnviron = "int_wood"; // Used by SurfIntWood, weapons fired while on this surface will have a reverb effect.
This value also determines the sound for footsteps inside of a building corresponding for the roadway LOD. It is important to use corresponding textures for surfaces that are indoors or outdoors, as it has an effect on the sound when firing weapons on that surface.
Check the spoiler for soundEnviron values used in vanilla A3 in 1.68:
normalExt water gravel concrete tarmac wood metal wavymetal roof_tiles int_wood int_concrete int_tiles int_metal normal sand dirt drygrass grass stony debris sand_exp rock seabed_exp tiling virtual dirt_exp concrete_exp asphalt_exp int_concrete_exp pavement_exp int_pavement_exp stones_exp int_solidwood_exp softwood_exp int_softwood_exp steel_exp metalplate_exp metalplatepressed_exp int_metalplate_exp gridmetal_exp wavymetal_exp int_carpet_exp int_mat_exp mud_exp straw_exp int_lino_exp lino_exp rooftiles_exp gravel_exp grass_exp grasstall_exp forest_exp↑ Back to spoiler's top
soundHit
String: Defines the sound played when the surface is struck by a bullet
soundHit = "concrete"; // Used by GdtStratisConcrete, sound of bullet hitting concrete is played when this surface is hit
soundHit = "soft_ground"; // Used by GdtStratisDirt, sound of dirt is played when this surface is hit
Check the spoiler for soundHit values used in vanilla A3 in 1.68:
hard_ground concrete soft_ground building
surfaceFriction
Float: Defines the surface friction on this surface (lower value = more friction)
surfaceFriction = 2.5; // Used by SurfRoadTarmac, highest surface friction value
surfaceFriction = 2; // Used by SurfRoadConcrete, above average surface friction value
surfaceFriction = 1.8; // Used by GdtDirt, below average surface friction value
surfaceFriction = 1.5; // Used by GdtMarsh, low end of surface friction values
T
tracksAlpha
Integer: Defines the alpha value of vehicle tracks
tracksAlpha = 1; // Default value used by all surfaces
transparency
Integer: Unknown
transparency = -1; // Default value used by all surfaces