Damage Description – Arma 3

From Bohemia Interactive Community
Jump to navigation Jump to search

Template:Cfg ref

Intro

An ongoing investigation on how damage and armor actually works in Arma 3. This page was initially based on Olds (talk) research during the creation of the Real Armor Mod ("RAM").

Sometime in Q1 of 2015, the RAM information will be removed from this page and relocated to its own wiki.

Damage vs. Penetration

It's important to understand that penetration and damage are not exactly the same thing in Arma 3--they have a slightly indirect relationship. For damage to occur, a vehicle must have:

Simply put: an attack must simultaneously penetrate 'both fire geometry and a hitpoint radius to cause damage to a vehicle.

Arma damage pen.jpg

Attacks A-D are examples of direct attacks (indirectHit & indirectHitRange = 0). Attack E is an example of an indirectHit attack. As the diagram shows, armor (in the form of fire geometry) can protect against direct damage--but indirectHit damage can easily occur without penetration (especially when indirectHitRange is large). Only a hitpoint's minimalHit and explosionShielding values can protect against indirectHit reaching through armor to cause damage.

Note: an indirectHit attack causes damage as long as any of the vehicle's fire geometry and hitpoints are in range--whether the hitpoint penetrated happens to be within the fire geometry penetrated is irrelevant.

damage pen vars.jpg

Consider the image above--assume the light blue rectangles constitute the fire geometry of a single vehicle. Only the two red-bullet indirectHit attacks cause damage. The blue direct attack fails to cause damage because it never simultaneously penetrates both fire geometry and hitpoint. The blue indirectHit attacks also fail to cause damage because they likewise never simultaneously "touch" both fire geometry and hitpoint with their radius of effect.

The consequences of the damage system for armor modeling is discussed later in this page.

The Typical Damage Process

This is how damage usually transpires with stock Arma vehicles (and most mod content as well, since it tends to conform to BI standards of vehicle creation).

Olds damage diagram sm.gif

1. Pre-impact

A projectile is headed for the target. (For our discussion let's assume its a kinetic round on track for a direct hit vs. an AFV)

2. Initial Impact

The projectile impacts the target. It has not penetrated any armor yet. And if it doesn't have the ballistics to go further it will terminate here doing only this initial damage. Regardless, the following things happen: Every major location on the target takes some damage. The location nearest the impact point gets the most, and it falls off geometrically. The target's global health is generally damaged the most. Several factors affect the amount of damage taken: obviously the hit value of the weapon is important, but various weapon & target config values are also involved (minimalHit, explosive, etc.). That's right, some damage has already been done regardless of whether it's pistol-round vs. tank or sabot vs. bunny. If the hit values are high enough, this initial impact alone can destroy the target (essentially by knocking out global health) ...regardless of penetration!

3. Penetrating Damage

If the projectile can penetrate the target's armor, it will continue moving and doing damage as it goes. Here's what happens: Every major location continues to take damage as in step 1. But something new happens as well... ...as the projectile travels past the armor it starts doing much more damage to the area immediately around itself. Global health continues to get damaged and can really get clobbered now. BTW, this happens even if every passThrough value is set to zero(!). The projectile will terminate here or travel on through the target if it has penetration power remaining to do so.

Keep in mind there are (sometimes significant) variations to how this works for things like explosive weapons, indirectHit, deflections, etc. More on those below. And, yes, this description holds true for human targets (shoot someone in the hand, and their head will take some damage).

Indirect(Hit) & "Explosive" Damage

IndirectHit

Olds iHit diagram sm.gif

This works pretty much as advertised--indirectHit represents damage from explosions (not to be confused with the BIS "explosive" property). indirectHit damage is applied whenever a weapon with that config property hits something (you, the ground, etc.) It causes damage out to 4x it's indirectHitRange (which is a radius), falling off linearly. If a target is within range (our trusty tank in the above diagram), it takes the same all-location damage described in part A. (The location closest to the impact takes the most damage and so on...) And just as before, global health takes the most damage. Ranged indirectHit damage bypasses your armor and damages you anyway. Only the explosionShielding (and minimalHit) property can mitigate this.

Note: the indirectHit 'explosion' radius effect appears to occur whenever a new surface is hit. This can occur just once when the ground is hit, or multiple times if the projectile has a high "caliber" and passes through several pieces of fire geometry.

Explosive

Not the "explosion" effect you're thinking of--that's indirectHit. This weapon property does only one thing: it controls how much hit damage falls off with speed. Weapons with no or 0 explosive value are considered fully 'kinetic' and lose hit value as they slow below their typicalSpeed. Weapons with explosive=1 are considered fully 'explosive' and do full damage regardless of the projectile speed. Values between 0 and 1 control the ratio of kinetic-to-explosive damage (i.e. explosive = 0.5 means half the damage falls off with speed and half does not). <!> QUIRK! Values >=0.7 nullify a weapon's armor penetrating ability (as if caliber=0)!. Use values <0.7 if you want your weapon to have normal penetration behavior!

Penetration & Ballistics

Bullet/Shell

Bullet/Shell ballistics are very simple and quite accurate. The only properties that influence trajectory are initSpeed (CfgMagazines) and airFriction (CfgAmmo). Such projectiles travel based on their muzzle velocity (initSpeed) and aerodynamic drag (airFriction), along with gravity-induced vertical drop. Penetration is simply a factor of (remaining projectile speed at impact) and (CfgAmmo.caliber).

Projectile slowing through armor (or any other kind of fire geometry), appears to be handled purely by the projectile's speed & "caliber" and the fire geometry's bulletPenetrability(WithThickness). "airFriction" ceases to be a factor unless the projectile makes it's way through the target back out into open air. No other target material properties (Density, etc.) appear to factor in to the simulation.

Missile/Rocket

Missile/Rocket ballistics are more complex (let's call them M/R's for short). However, unlike Bullet/Shell penetration--which works quite well--M/R penetration is broken in the Arma 3 code. BI ignores penetration effects for these weapons and relies on exaggerated hit/indirectHit values to cause target damage. (RAM fixes this bug/limitation--and adds some new features along the way--with some scripting).

Unguided

These projectiles still use the same two properties as Bullet/Shells to determine their trajectories, but add some more (all in CfgAmmo): initTime, thrust, thrustTime, and maxSpeed. The four new properties account for the additional effect of a rocket motor: after "initTime", "thrust" is added to accelerate the projectile until it runs out ("thrustTime"), while "maxSpeed" puts a cap on the projectile's top speed. "sideAirFriction" & "maneuvrability" (from CfgAmmo) and mass (from the P3D model) get honorable mention here. But it's not clear that they add anything to the simulation of unguided M/R trajectories.

Guided

These projectiles work as unguided M/R's above, but with added properties to account for the fact that they manuever to track a target. "sideAirFriction" is used like airFriction to create drag, but in the lateral axes (as the missile turns to follow a target). "manuevrability" controls the rate of turning ability (mass may also play a role here--in that higher mass M/R's have a harder time turning due to momentum--but testing is required to confirm this). There are also a few simple properties that pertain to how tracking is achieved, but they are beyond the scope of this discussion.

Ballistics and Network Code

Unguided Bullets, Shells, and Rockets (simulation = "shotRocket") ballistics are calculated locally/on the client only. They do not cause undue network traffic in multiplayer. Guided missiles on the other hand (simulation = "maverickweapon") broadcast their trajectory over the network, generating much more data traffic in multiplayer every time one is in flight. Think of guided missiles as little airplanes, clogging up the network with traffic as they fly around.

Limits & Peculiarities of the Penetration Sim

Arma fully simulates the trajectory through a piece of fire geometry only for projectiles that make it all the way through. The game does not properly simulate movement within fire geometry. If a projectile is stopped by a piece of fire geometry, the game treats it essentially as if it stopped at the surface. (This is noticeable if you fire weapons while using a projectile tracing script).

Furthermore, if you fire a sufficiently high "caliber" bullet at a series of plates with setAccelTime set very low, you will notice a related curiosity. The bullet will slowly approach the plates and then appear to 'zip' through them in rapid succession, only slowing back down when travelling through air. This is also a consequence of the penetration code 'shortcut'. A bullet's travel time while inside a piece of fire geometry is not represented. As soon as the bullet impacts the geometry, the game calculates whether it has enough penetration to make it through. If it does, the bullet is instantly teleported to the other side of the geometry. (If it doesn't--as discussed above--it stops at the surface).

The one exception to this is hitpoint damage. The game does (instantly) calculate the precise depth of a partial penetration for the purpose of determining whether any hitpoint radii were hit.

Armor Methods & Recommendations

This section contains advice about designing your vehicle's fire geometry ("FG") and hitpints based on the research presented in this elsewhere on this page.

Fire Geometry Placement

Some 'rules of thumb' regarding the preparation of vehicle FG:

  • Use the most detailed and accurate armor data you can when creating your vehicle's P3D FG (armor). Correctly calibrated weapons are only going to give realistic results if your armor settings are realistic.
    • Use accurate thicknesses, accurate angles, and accurate materials. Arma's penetration simulation is very detailed and takes all these factors into account to generate an accurate "line-of-sight" path of a projectile through vehicle materials/armor.
    • Of course, the FG model is simplified and does not need to contain every little piece of geometry. Use just enough detail to capture the key armor areas of the vehicle (the Samples_F T-72 tank is a reasonably good example--although it could be just a bit more detailed).
  • The material used for armor pieces should usually be "armour.rvmat" (with thickness is defined by your model geometry). Preset-thickness materials ("armour_plate", etc.) respect LOS thickness, so you can use those where necessary.
    • Regardless of what the real vehicle uses for armor (aluminum, composite, etc.), the best practice is to translate them into RHA-equivalent thickness. (To be specific, we are speaking here of "RHAe-KE": the equivalent thickness of rolled homogenous armor steel vs. kinetic attack).
  • If there is important internal structure, it may may be blocked in crudely per the T-72 sample model. It is acceptable to model hitpoint vertices inside pieces of FG (e.g. the T-72's cast-iron modeled engine block).
    • However, it is not necessary to fill a vehicle with internal FG. In fact, it should be avoided as it increases the chances of a penetration error (see the next point below).
  • Avoid overlapping FG at all costs--Arma can make errors as a projectile travels through interpenetrating pieces of FG (the greater the interpenetration, the more likely the error). Arma projectiles tend to only "notice" the first piece of FG they hit if other FG is embedded within it.
    • In fact, it's desirable to leave some space--at least a few cm--between pieces of FG that don't need to be directly touching.

Hitpoint Placement

As discussed earlier, Hitpoints are required for a vehicle to take damage. The style of hitpoint placement affects how a vehicle takes damage with respect to things like armor and penetration. One of the reasons that (stock) Arma vehicles take damage in the somewhat puzzling way that they do is due to their choice of hitpoint placement.

Hitpoint Radii

Recall from the "Damage vs. Penetration section that an attack must simultaneously affect both fire geometry and a hitpoint to produce damage. Consider the following two approaches to hitpoint placement for the same vehicle--the front view of a simplified AFV:

Traditional Arma Approach

armor-hp-1.jpg

Modified "Internal" Approach

armor-hp-2.jpg

In the first approach, the vehicle will take damage from non-penetrating hits. This is because the virtual spheres created by the hitpoint radii (the purple circles) poke outside the vehicle's FG (the blue and gray polygons). In the second approach, the hitpoints are constrained to be inside the armor layer wherever possible. The second vehicle will not take damage from non-penetrating hits. Obviously, if you have non-armored parts of a vehicle that should be damaged by non-penetrating hits (tires, glass windscreens, structural steel, etc.), then their hitpoint spheres should "poke through" the FG in the "stock" manner.

Hitpoint Stacking

Now let's consider two different approaches to hitpoint "stacking":

Traditional Arma Approach to Stacking

armor-hp-4.jpg

Modified "Overlapping" Approach

armor-hp-3.jpg

In the first example, hitpoint spheres are stacked so they do no overlap. This appears to be the default approach to hitpoint placement in Arma 3. The second approach allows the spheres to overlap, with two resulting benefits:

  • Usually, a smaller number of higher-radius sphere can be used to define a given volume.
  • There are less "holes" between the spheres where a projectile can pass through without causing damage.

There don't appear to be any negative side effects to the overlapping approach; for example, overlapping spheres do not cause "extra" damage when a projectile penetrates through the overlap. BI itself increasingly has been using overlapped hitpoints in their models, so this approach should be considered safe.

Hitpoint Placement Recommendations

In summary: combine the two "modified" approaches for improved armor and damage performance.

Note: to be fair to BI, they have been moving away from what's referred to as the "traditional Arma" method of hitpoint placement above. Looking at current revisions of the game, you will notice that their tanks in particular tend to be much closer to the "modified" approach. So perhaps one should refer to it as the "old-fashioned Arma" approach.

Hitpoint Properties

(armor and indirectHit...)

Concluding Remarks on Armor & Penetration in Arma 3

In vanilla A3, the effects of armor are largely ignored by the damage system. More accurately: armor penetration is present, but its significance is overwhelmed by the global hitpoint effect--this due in large part to the way hitpoint "spheres" are placed in stock Arma vehicles and the effects are particularly dramatic for high damage-value weapons. Caliber-based ballistics work very well, but caliber is bugged for rockets & missiles (it can't be added). Nor can the submunition feature be used as a workaround (it is also bugged for missiles if not other weapon types). A script-based approach must be used to enable those weapon types to penetrate armor correctly. RAM contains such an approach.

Adjusting Config Properties for RAM

(Expand for a summary)

(See the Config Properties Mega-List for an explanation of the properties themselves).

Weapon-related Config Properties

airFriction, caliber

RAM adjusts caliber & airFriction values based on real-world data whenever possible. This yields accurate penetration values and ballistic trajectory. It corrects the Missile/Rocket penetration bug by editing those weapon types to create regular (bullet/shell based) projectile submunitions on impact, restoring penetration ability. (Rocket & Missile improvement cannot be achieved by adjusting vanilla configs - this requires script adjustment).

explosive

RAM either caps explosive values at <0.7 to prevent the no-penetration bug, or creates a penetrating submunition (e.g. HEAT warheads).

hit

BI tends to greatly exaggerate hit values for large caliber weapons, while RAM generally reduces them values to prevent armor-overwhelming damage.

Vehicle Config Properties

Global:

armorStructural

RAM generally ramps up these values to more or less cancel out the effect of global damage. (BI seems to have taken up the idea, and is creeping up armorStructural values in more recent configs).

Hit Location:

explosionShielding

These values are usually much lower in RAM than vanilla A3 (i.e. more protection against indirectHit).

passThrough

These tend to be zeroed out in RAM.

radius

[#>0,m?] the radius (in m?) of the location's hitpoint vertices in the vehicle's P3D model. The idea here is to spread the vertices throughout the internal structure such that they do not spill out into or beyond the vehicle's armor plates. Unless you have control over the P3D source file, you probably don't want to mess with this value.

HitTrack

[location class] Keeping in mind that this location generally has no armor geometry protecting it and is thus easily damaged by the slightest hit, RAM generally increases the protective properties of explosionShielding and minimalHit to make tracks more resistant to minor weapons.

Useful Links

See if you can pick out the useful data from the obsolete!

VBS:Damage Modeling:Objects

VBS:CfgAmmo Reference

VBS:Damage Flowchart

VBS:Damage Modeling:Simulation Formulas

Config Properties Mega-List

Template:Cfg ref